Boating
Bilge Pumps
Bimini Tops
Boat Anchors
Boat Insurance
Boat Ladders
Boat Loans
Boat Maintenance
Boat Motors
Boat Paint
Boat Prices
Boat Propellers
Boat Repair
Boat Safety
Boat Seats
Boat Steering
Boat Trailers
Boating
Buying a Boat
Cleaning
Corrosion
Inboard Engines
Life Vests
Marinas
Marine Stereos
Mold and Mildew
Navigation
Oil
Outboard Motors
Selling a Boat
Stern Drives
Stringers
Swim Platforms
Transom
Trim
Trolling Motors
Twin Engines
VHF Radios
Waxing Your Boat
Winches/Windlasses
Winterizing Your Boat
Wiring
|
| |
 |
Results 31 - 60 >> |
|
Related Topics On Epoxy
- Repairing Transom of Quicksilver Inflatable, Pls Help
...glue and seal with West System epoxy. Also, use stainless...
- Fiberform stringer replacement update. Stringers aren't one piece!
...butt joint. A little epoxy or waterproof glue... ...of the glass. I used epoxy to reattach the pieces... ...laid down a bed of epoxy for a strong bond....
- Should I redrill Splashwell holes??
...then cap them with epoxy or fiberglass. You... ...good idea to work some epoxy or sealant in around... ...inside surface with epoxy and let it dry. Then I would either epoxy the brass tube in place...
- YES! IT CAN BE DONE BY A ROOKIE!
...working, 3 gallons epoxy resin, 120 sq. ft....
- Soft Spots?
...if they didn't use epoxy to laminate the glass...
- Transom repair
...Polyester works ok but epoxy is better.. If u use epoxy be s... ...is compatible with epoxy..... P.S. regular... ...Definately use EPOXY resin , IMO poly... ...cheap and absorbs the Epoxy well. That was 5 years...
- Holes in transom. . . .
...of the transom with epoxy. This keeps water from... ...drillings. Let the epoxy soak into the coring. When the epoxy hardens, then fill... ...complicated immediately, (epoxy or synthetic). If I... ...would go for a little epoxy resin, a bolt, a couple... ...Did it last summer, Epoxy proper dia. dowel...
- Replacement Material Help
...Use an epoxy called PC-7 it will hold some 5 min epoxy should work also if...
- Cloth, carbon,kevlar OH MY! What glass do I use for stringer repair?
...that the cloth isn't epoxy resin friendly. Is... ...fillers to make THICK epoxy an trough in a fillet... ...the stringers with epoxy.. just run cloth up... ...roller & frame.. roll epoxy on the thirsty bi-axail... ...! I'm going with the epoxy resin. What... ...buy to mix with the epoxy? Also, there are so...
- Deck rot,need advise on resins please.
...resins be used over epoxy resins? We are also... ...but believe it to be epoxy. Boat is a 1989 Bayliner... ...You can put epoxy resin on top of polyester... ...polyester on top of epoxy.factory built boats... ...for days. if you use epoxy, wear a respirator,... ...not hold to existing epoxy, yet expoxy...
- Transom Rot??
...plases too. It's an epoxy that can be injected... ...transom to inject the epoxy. It will expand 10%... ...same holes for the epoxy.... ...place to insert the epoxy you will also be able...
- Need Hull Repair Info
...purchase Gougeon Bros. West System publication # 002-520... ...would work, but I use West System epoxy mixxed with any of... ...purchase Gougeon Bros. West System publication # 002-520... ...would work, but I use West System epoxy mixxed with any of...
- Help hole in fiberglass boat
.... You can use either epoxy or polyester resin,... ...soaked in the resin (or epoxy) -- Just lay the cloth...
- Please help..the log is still in the hull
...you can spring for epoxy, if you may... than... ...personally I would use epoxy (remember once you use epoxy for the repair you... ...from what I am seeing epoxy may be the way to go... ...already is... but epoxy would be great ,too...
- Champion 17'
...reglass, try to work epoxy in under it, sell or...
- Anybody replaced rub-rail vinyl insert ?
...home depot and just epoxyed the rope in. looks...
- Transom repair advice needed
...these in with thickened epoxy? Or do I have to grind... ...better then thicken epoxy....just make it thick... ...a coat of NON thick epoxy first as not to suck... ...cutout with thickened epoxy (I use sawdust), and... ...fiberglass piece to the epoxy-encased plywood, countersinking...
- Aluminum Repair
..."Seafit Penetrating Epoxy". Would there be something... ...those repaired, just epoxy, on all sides, the...
- Replace transom...do it yourselfer?
..., pick up a copy of West System's book, "Fiberglass...
- Fiberglass spider cracks.
...that is published by West Systems, it is available at...
- Dents in toons
...undamaged portion and epoxy it over the... ...large panel aircraft epoxy used for auto panels... ...cosmetic appearance. The epoxy is incredible stuff... ...new automotive panel epoxy is great stuff (real... ...just fill holes with epoxy or polyester putty.... ...The panel epoxy should not be seen....
- Wet transom - what now
...fill the hole with an epoxy filler such as Marine... ...get a sample kit of epoxy from... ...that will have all the epoxy and thickners yu will... ...hole with unthickend epoxy with severial coats... ...Then thicken up some epoxy to about peanut butter...
- Boat hull problem
...bit then fill with an epoxy then place packing... ...set.. Wipe off excess epoxy with... ...Drill new holes when epoxy cures....
- Decking
...right. Now days with epoxy you cna totaly waterproof...
- Transom problem?????picture
...fill the hole with epoxy and a ss screw....
- Sea Nymph 12K Aluminum
...panels out using MARINE EPOXY and clamps. Then it...
- Redecking a pontoon boat
...you apply 2 coats of epoxy to both sides AND... ...Soak the edges with epoxy. Coat both sides with... ...after installation. Epoxy is too brittle without...
- Add a consol
...attach with west sytem epoxy mix in the thicker...
- Filling holes in center console
...Marine-tex epoxy putty found in any...
- First time out front heavy?
...glass cloth soaked epoxy on cracks then use...
|
|
|
